Unfortunately, as much as I like and use firefox on both pc and mobile, chrome and chromium based browsers dominate the market. It doesn’t help that they come pre-installed in both cases.

Beep boop ah shiet… They done got me this time… runs away leaking oil and steam

Not all bots are bad, the piped bot is nice and there are others too

If you go the zigbee route I recommend this one, works well and supports direct binding too: https://zigbee.blakadder.com/Gledopto_GL-SD-001.html

Stay away from the Moes, takes like 1.5sec to get to full brightness when turning on and you can’t get rid of the delay.

If you are fine with relays as well look into Nous modules, I got a dual channel relay module from them that works very well, also supports direct binding. They might have dimmers too, but I haven’t used them myself.

All these require neutral though, can’t speak of their non-neutral versions.

Not all IoT is bad… If you decide to get some cloud IoT and keep it on the main network that’s on you, but you could have a separate vlan or even a separate protocol like zigbee and z-wave to secure these devices and control them locally with home assistant. It might not be good enough for highly sensitive enterprise environments, but more than enough for average Joe who’s not being targeted by APTs or espionage

The aqara endpoints I have are solid. But one aqara mains powered relay is causing delays with an aqara door sensor when connected to it. Aqara implemented some strange stuff in some of their zigbee devices

The guide on the official website has a few recommendations for network zigbee coordinators as well: https://www.zigbee2mqtt.io/guide/adapters/ I cannot recommend any as I am using a USB coordinator. But you can also jump on the official Zigbee2Mqtt discord and ask for recommendations there, you can find it linked under support on the website.

I recommend you join that discord as there might be issues that come up and there are a few people on the server that could help you with the troubleshooting.

One thing you have to keep in mind is that you can’t place the zigbee coordinator near other 2.4GHz networks like wifi APs/extenders, bluetooth adapters or microwaves. Well, you can, but you will run into many issues.

If you do decide on the sonoff stick make sure you get the P version, not the E version as the later is under experimental support and better for ZHA. You can also have a look at the other zigbee recommended adapters for Zigbee2mqtt: https://www.zigbee2mqtt.io/guide/adapters/

Zigbee devices are already cloudless local devices, you don’t have to flash them unless there are alternative firmwares that add functionality you desire.

They also need a coordinator to comunicate with HA. You can get a zigbee stick, depending on how you plan on integrating these devices there are some chipsets you should look for. If you want the easy route go for ZHA and maybe the skyconnect stick, otherwise you can go with zigbee2mqtt route which supports more devices and is more customizable and look at their list of recommended coordinators.

Most mains powered zigbee devices act as router and extend the newtork, not all of them do and not all that do are good at it. Some manufacturers use custom implementations of zigbee like Aqara which can cause issues.

I use zigbee2mqtt with a sonoff P stick and I am happy with it, it’s not as plug&play as ZHA, but it’s easy to add support to new devices if they are not already supported.

A relay will do what a relay does, turn on and off. No matter what software you put on the smart plug, it can’t really become too dangerous. Unreliable maybe, but most of these smart plugs are just that, a dumb relay controlled via a microcontroller

When I was looking for a pi4 I stumbled upon orange pi, rock pi, banana pi and libre computer. They have models both cheaper and more expensive than the rpi. All depends on the specs you need.

Not sure where you’re from. But here is a random one from ebay . You will find many like it. I got this model with 4gb ram, 256 ssd and power supply for ~80€ on europe, much less then I could pay for any PI4 at the time that came with no case, no psu, no ssd. It idles around 3-4w headless with no peripherals running home assistant. There are other models too ofc. Just have a look around used hardware stores if you have them around your area.

You can get thin clients for much less than that… Better performance if needed, similar power efficiency for similar loads, they sometimes bring storage, power supply and ram and you don’t generate more e-waste as these are already being thrown out by many big companies every few years.

The only reason to go for the PI is if you really need the GPIO, the tiny form-factor and even then there are cheaper alternatives with similar or better spevs.

I have both eternity and infinity installed from f-droid and each opens up fine. Tho inifnity no longer wroks, guess it’s time to uninstall it

You should give eternity a try. It is using the infinity UI which worked pretty well on my tablet. You have to add a custom repository to f-droid or use obtainium to install it